What is the production mode of the non-woven screen printing machine? Non-woven automatic screen printing machine introduction

The color grading can be completed in a short time. Related concepts Etching etching, also known as photochemical etching, is a technique for removing materials by chemical reaction or physical impact, and can be classified into wet etching and dry etching. (dry etching) two types. The screen hole of the image portion is blocked.) The squeegee is pressed during printing. Another method of cutting is to use a 4mm × 50mm ruler, and the glass knife is cut close to the ruler. The netting selects the screen and the net frame to combine the two. This is the stretch net. "painted" out of the colorful pattern to come. In addition. The acid will turn the glass into a black. How to make a glass carving artwork is a flat relief. The deep carving is usually done with a high-speed sand blasting machine and an air compressor. After the glass surface is pasted with a special protective film, use a utility knife. Engraving the pattern. Use the air compressor to drive the high-speed sand blasting machine to complete the engraving. This kind of investment is relatively large. The set should be around 20K. There is also a hand grinding wheel for engraving. Install the glass cutting with an angle grinder or a hand drill. Sheet or other glass grinding wheel. Engraving and polishing on the surface of the glass that has been moistened with water. This method is also applied to the three-dimensional sculpture. The equipment is cheaper. In the ordinary hardware store, you can buy the corresponding angle grinder or hand. Drill. You can buy the corresponding grinding wheel in the glass tool shop. The price is about a few K. There are two ways to control the color difference of silk screen glass: There is a base color. The process flow is as follows: stretching net → sizing → drying → printing → development → drying ↓ flat glass → cutting → edging → cleaning and drying → printing ↓ sintering 1 . Therefore, after the deployment, it will do a certain comparison test. And baked at high temperature. Paste the paraffin along the lines until the glass is visible. Apply hydrofluoric acid (available at pharmaceutical and reagent stores) to the inscribed lines. Try shaking the drill. Related Concepts Drilling and drilling is the operation of machining a hole in a solid material with a drill bit. Cutting the embossed glass with a glass cutter The embossed glass is cut with a glass cutter, and the embossed surface should be downward, and the cutting method is the same as that of the wired glass.

Bubbles in the ink. The plant material, including roots, stems, leaves, flowers, fruits, bark, etc., is dehydrated, preserved, pressed and dried to form a flat flower material. After careful design, it is made into a beautiful decorative painting, card and daily necessities. Plant products, integrating the art of botany and environmental science. Cut off the corners. Processing range: Glass material requirements: flat glass, float glass, ultra-white glass, frosted glass, tempered glass glass Size requirements: 1500mm * 2500mm Glass thickness requirements: 4mm-20mm Voltage: 220V Can process Shaped: Allows a certain range of profiled processing related concepts Glass glass is an amorphous inorganic non-metallic material, generally using a variety of inorganic minerals (such as quartz sand, borax, boric acid, barite, barium carbonate, limestone, feldspar, soda ash, etc.) The main raw material is made by adding a small amount of auxiliary raw materials. Pay attention to alignment; turn on the power. It seems that mystery is not difficult. Glass is light-transmissive and reflective, and easy to color. It is often used in applications where lighting and color are required, such as optical instruments and various art decorations. There are a series of plate making methods in which a letter type is arranged in a movable type, and a letterpress type is cast into a copy type to cast a letterpress and a picture is obtained by photo or electronic color separation, and a negative plate, a lithographic plate, a gravure, and the like are formed by using a negative film. Remove the dirt from the car glass before the car glass is repaired. There are many factors affecting the quality of the printing plate in the plate making, mainly the developing solution concentration, the developing temperature and the developing time, the circulation stirring condition of the developing solution, and the degree of fatigue deterioration of the developing solution. The art glass hand-blown method glass is a cup whose raw material is glass. The art of embossing is the use of pressed flowers to create the basic materials of art. Embossed embossing is derived from the English pressed flower, which translates directly into "embossing". The glass is conveyed to a light-solid oven for light solidification; Grinding the non-corrosive part of the glass into a "matte type" is even more graded. How to make the ice crystal glass first spread the printed picture on the conveyor belt; evenly apply the photo glue; press the glass On the drawing paper. Modern technology has brought new vitality and vitality to the glass industry, and has also greatly improved the performance of glass.

After finishing the line, there is no success. Put the glass knife under the glass and the glass on the table. The knife is also placed under the glass on the table. Facing the scratch marks, bring the gloves, pay attention to safety, and the palms of the two hands are separated. Hold the traces on both sides, the average position of the edge of the glass, both hands and palms at the same time force, be quick, fast, do not slowly force, hear, slam, immediately force, prevent the separate glass from pressing hard on the table Causes rupture. After the repair, the effect is very good, but after a while, the crack seems to appear again: the common reason is overheating. It is a suitable temperature to heat the glass to 26--32 °C. After this temperature, the glass will expand and the resin will be Extrusion, so it seems to have been repaired at the time, in fact, some of the resin in the crack has overflowed, and the crack will appear again when the glass cools down. Another reason is that the pressure is too great when placing the repairer or pushing the piston, which will produce the same phenomenon as when it is overheated. The solution to this problem is to rotate the piston one more time when it touches the glass, by adjusting the screw behind it. Make horizontal adjustments. Lighter drying is lighter than undried.

Article source address: http://